1994 PHAZER 2 LE PROJECT

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
It’s coming together! I got the hood mounted again and reinforced with some flat aluminum. Nose cone should be here this week and then some minor pipe repairs…
IMG_9584.jpeg

IMG_9586.jpeg
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
Give it to me straight… can a guy cut this bend out of the pipe, and patch it? The bottom half is fine, it’s the top half.

IMG_9602.jpeg
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
It could be done. But why not look for a Bender or Aaen pipe.
100% looking but also trying not to spend a bunch. Honestly would put a stock pipe on for now to get it running and on the snow
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
yea that will be the next task. get it red? Ill have to make some bungs for the ends...
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
I ordered some 7 tooth drivers and I have a used 1-1/4" ripsaw track for it too... lots of time before November 23!
 

pipes

Active VIP Member
Joined
Dec 23, 2008
Messages
26,688
Reaction score
37,468
Location
Bonnyville Alberta
I’ll give my buddy a call tonight and ask him if he still has that 92 Phaser II that I sold him. I sold it to him with the Aaen pipe and threw in the Stock pipe. Maybe can swing a deal with him.
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
I’ll give my buddy a call tonight and ask him if he still has that 92 Phaser II that I sold him. I sold it to him with the Aaen pipe and threw in the Stock pipe. Maybe can swing a deal with him.
Thank you!
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
I had a buddy successfully repair the stock pipe and I warmed the sled up, on a stand with the track off the ground, it still only revs to 5100rpm….

Compression test and go from there…
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
Sitting at work wondering if the choke cable setting could make it so fat it won’t rev out? The machine responds to the choke though…
 

Clode

Active VIP Member
Joined
Jan 8, 2012
Messages
29,550
Reaction score
46,587
Location
BC
Sitting at work wondering if the choke cable setting could make it so fat it won’t rev out? The machine responds to the choke though…
They can hang open just a little, spray some brake clean down the choke circuit and make sure they seal. If they don't remove the choke cable and check again, maybe the cable is dragging. I am not sure if the choke plungers on that year have the rubber seat surface or the rubber o-ring in the middle of the plunger, if it does they are likely toast. Those carbs may also have had a rubber plug in the one circuit in the carb bowl next to the main jet circuit, are they there?
 

NoBrakes!

Active VIP Member
Joined
Nov 13, 2011
Messages
6,317
Reaction score
12,797
Location
Edmonton
They can hang open just a little, spray some brake clean down the choke circuit and make sure they seal. If they don't remove the choke cable and check again, maybe the cable is dragging. I am not sure if the choke plungers on that year have the rubber seat surface or the rubber o-ring in the middle of the plunger, if it does they are likely toast. Those carbs may also have had a rubber plug in the one circuit in the carb bowl next to the main jet circuit, are they there?
No joke, I was waiting for your input/opinion.

I want to say it has the rubber surface plungers not o rings and they were still soft and flat when I looked last. I did put the black rubber plugs in the right spots but I am going to have to confirm that again...

Any tips to adjusting the chokes correctly?
 

Clode

Active VIP Member
Joined
Jan 8, 2012
Messages
29,550
Reaction score
46,587
Location
BC
No joke, I was waiting for your input/opinion.

I want to say it has the rubber surface plungers not o rings and they were still soft and flat when I looked last. I did put the black rubber plugs in the right spots but I am going to have to confirm that again...

Any tips to adjusting the chokes correctly?
To adjust the cable back off the adjusters at the carb plungers and at the choke lever there should be some free play. The free play is checked when the choke is in the off position and you lightly pull out on the piece that the lever attaches to. Do not flip the choke lever at all, leave it in the off position. With the choke adjuster nuts backed off you should be able to pull this out quite a bit until resistance is felt. That resistance is the plunger starting to lift and the spring above the plunger compressing. You only want to be able to pull the cable out to about 2-3mm of free play. I will adjust one at a time, you will be able to feel the reduced free play as you go. When I feel the change initially I stop and adjust the other side until I feel it starting to take up some free play. Then adjust both slowly until the 2-3mm is achieved. I then confirm the choke operation with fluid at the closed position.
 

Clode

Active VIP Member
Joined
Jan 8, 2012
Messages
29,550
Reaction score
46,587
Location
BC
Are the TORS wires still plugged in? These are yamahas throttle safety switch. They cause lots of issues.
 
Top Bottom