What did you do for your ATV today?

whoDEANie

Active VIP Member
Joined
Feb 8, 2009
Messages
4,633
Reaction score
8,479
Location
Edmonton
Finally catching up on the maintenance and repairs! Just finished replacing rear brake caliper on the outty. One one grizz, sticking throttle body is cleaned up and good as new, new control arm and stablizer bushings, primary is cleaned up and repacked, all new fluids. I just have to figure out how to finish pressing out a wheel bearing that fell apart on me. On the other grizz (rolled by the GF), got most of it torn down and ordered all new plastics, racks, and headlight/bumper plastics.

Whew, I still have a lot of work to do but it feels like I'm getting close.
 

Lem Lamb

Active VIP Member
Joined
Apr 5, 2010
Messages
4,286
Reaction score
7,808
Location
Lacombe AB
Please take the time to inspect upper & lower A-arms if your unit has them.

Check for cracks as well as bolts that keep things in place and frame anchoring points.

Just seen a SxS sitting in ditch along hwy 12 with broken top A-arm and other damage that goes with it when it became came cross threaded and side ways. Looks like it did the steering link in, back side fender where the tire ended up crinkled up some plastic, but sure it will be ok.
 
Last edited:

imdoo'n

Active VIP Member
Joined
Jan 15, 2008
Messages
58,435
Reaction score
51,892
Location
alberta from the back porch
Please take the time to inspect upper & lower A-arms if your unit has them.

Check for cracks as well as bolts that keep things in place and frame anchoring points.

Just seen a SxS sitting in ditch along hwy 12 with broken top A-arm and other damage that goes with it when it became came cross threaded and side ways. Looks like it did the steering link in, back side fender where the tire ended up crinkled up some plastic, but sure it will be ok.

Arff out for a ride today?
 

Lem Lamb

Active VIP Member
Joined
Apr 5, 2010
Messages
4,286
Reaction score
7,808
Location
Lacombe AB
Ha Ha. It could of been him since he might not of told us that he owns a red Razor that is now sporting 3 wheels.

He did mention it makes him faster. :rino:
 

Absledder

Active VIP Member
Joined
Oct 29, 2013
Messages
758
Reaction score
681
Location
bonnyville
Put on a 2" super atv lift, then went to put on my new zillas. Unfortunately I never thought about new lug nuts so I guess I'll have to wait till tomorrow to get the new tires and wheels on.


Sent from my iPad using Tapatalk
 

buckie

Active VIP Member
Joined
Dec 11, 2009
Messages
859
Reaction score
1,066
Location
Red deer
Went for a quick ride this mornin, smoked a rock effed a ball joint....drove to town ordered a ball joint....waiting for said ball joint...stupid rock

Sent from my SM-G920W8 using Tapatalk
 

WarrenG

Active VIP Member
Joined
Jun 9, 2015
Messages
258
Reaction score
369
Location
Edmonton
Mounted 40" light bar and installed sport low mod. New pitbull growlers mounted on set of oem wheels for a second set of tires to go with the stock bighorns.
Marine fuse block and second battery next.
 
Last edited:

arff

Active VIP Member
Joined
Apr 21, 2009
Messages
142,086
Reaction score
56,162
Location
Leduc
Can you post pictures of marine box?

I found sport low worked good.
Quick throttle response
 

WarrenG

Active VIP Member
Joined
Jun 9, 2015
Messages
258
Reaction score
369
Location
Edmonton
image.jpg
Will be using this with a 100 amp circuit breaker just for peace of mind.
 
Top Bottom