Stuff to watch for on the 18+ cats.

[snochuk]

Its always best to change gears and chain as one but yes you can. I have on a few occasion just did one.
I would at least do bottom and chain and run the top gear if it looks good.

When you leave a component in like a gear the chain will quickly stretch to match, faster than normal wear.
You will have the stronger upgrade components but in short time they will have the same wear as before.
Change everything at once.

 

[skegpro]

Where is the best place to order hyvo?

 

[Lund]

When you leave a component in like a gear the chain will quickly stretch to match, faster than normal wear.
You will have the stronger upgrade components but in short time they will have the same wear as before.
Change everything at once.

I completely agree, that is the best thing to do.
If you have little hours and wear you can get away with mismatch but your correct that is best.

 

[Cat401]

Does anyone know the width of the chain? Is it a 13 wide or a 15 wide.....
If its a 13, is there room to swap it to a 15?

 

[Cat401]

ok, I see the 18 Mountaincat is a 13 wide but they went to a BorgWarner chain.

I wonder is a 15 wide is do-able. You would have to change sprockets to match but then it would be pretty much bullet proof....wouldn't it?

We did this years ago on our Firecats......never busted a chain or had any issues again.

 

[Lund]

Where is the best place to order hyvo?

Check with Speedwerx. I think that is where my dealer was getting it from.
I have a pretty good dealer, parts man is resourceful and knowledgeable. Not all dealer are that way.

 

[tmo1620]

So what r you gonna do with that sled you just won

Lol how’d you find out about that , damn inter webs, not sure yet, still debating that, pretty cool Christmas present anyway

 

[skegpro]

Lol how’d you find out about that , damn inter webs, not sure yet, still debating that, pretty cool Christmas present anyway

Lol, I have my ways.
I'd ride em like water skis.

 

[Jorgy]

Where is the best place to order hyvo?

Talk to dragonweld on here, BDX/SSI sells Hyvo gears and chains

 

[skegpro]

Found some hyfax in the alphas clips........

 

[rhody605]

Found some hyfax in the alphas clips........
//uploads.tapatalk-cdn.com/20181231/baa8321f9e4a36eb873fd46e4d985f5c.jpg//uploads.tapatalk-cdn.com/20181231/802115aae89ca48226091b5ebdca28e7.jpg

We had that on our first ride out as well.

Was advised by Arctic Cat to tighten track.

Checked track and was super loose.

Tightened to normal specs and haven’t seen it happen again yet.

 

[skegpro]

We had that on our first ride out as well.

Was advised by Arctic Cat to tighten track.

Checked track and was super loose.

Tightened to normal specs and haven’t seen it happen again yet.

What is the spec?

 

[Bergler]

We were told 2" with 20lbs. We had same issues at the start. Tightened up and changed hyfax. Have not seen since. Track has been stretching a bit.

Anyone else getting a far amount of snow under the hood? had both steering boots packed full and steering was freezing up. I am sure I had the hood on correct, clutch was not slipping. But pain in the butt, have to give the steering a good hiyah in the middle of your sidehill to free it up.

Where is it coming from? The vents? anyone have similar issue or fixes.

Thanks

 

[skegpro]

We were told 2" with 20lbs. We had same issues at the start. Tightened up and changed hyfax. Have not seen since. Track has been stretching a bit.

Anyone else getting a far amount of snow under the hood? had both steering boots packed full and steering was freezing up. I am sure I had the hood on correct, clutch was not slipping. But pain in the butt, have to give the steering a good hiyah in the middle of your sidehill to free it up.

Where is it coming from? The vents? anyone have similar issue or fixes.

Thanks

Yes, this solves it.

 

[Bergler]

This a custom cover I would guess? Expanded metal with some fabric over top? Also which vents kit is that on the sides?

Thanks

 

[tmo1620]

There is also some little holes in the font nose cone on each side that need to be taped off, they look minor but make a big difference, a little 1cm by 1cm piece of gorilla tape in each hole will fix it

 

[skegpro]

This a custom cover I would guess? Expanded metal with some fabric over top? Also which vents kit is that on the sides?

Thanks

Bought the side ones from moflo.

And the center I took out the goggle holder and replaced.it with the grill piece from the early release or snopro model. It's plastic, cost $15 bucks from Cat.

Then I bought a sheet of hydroforbic prefilter material from moflo, cut and glued it into place.

It has been awesome, really lowered the engine bay temps and the sled can always get cool intake air.

 

[Catrider16]

This a custom cover I would guess? Expanded metal with some fabric over top? Also which vents kit is that on the sides?

Thanks

You can buy a vent kit and it fits properly. I have the same one on mine, works well.

 

[chevy]

Who’s vent kit are you running

 

[killerrf]

https://www.moflowvents.com/2018-arctic-cat-ascender-8-piece-kit/
Had these vents on two proclimbs. Best vents money can buy in my mind. Very durable.