yamaha codes

[jbb]

--------------------------------------------------------------------------------

Here is a list of trouble codes for Yammis (Genesis 120 engine):

15 - Throttle Position Sensor and Circuit problem
16 - Throttle Position Sensor stuck
21 - Coolant Temperature Sensor and Circuit
42 - Speed Sensor
46 - Power Source Voltage
80 - Grip Warmer Switch and Circuit
81 - Grip Warmer and Circuit
82 - Thumb Warmer Switch and Circuit
83 - Thumb Warmer and Circuit
84 - TORS System Activated(throttle override)
86 - Cold Engine Protection Activated


hope this helps some of you!

 

[RaspberryNytro]

Thx jbb............. that'll come in handy someday!!!

RN

 

[jbb]

Yamaha Error Codes for Apex, Attak, and Apex Mountain models


Code #
Item
Symptom
Fail-Safe Action Starting Capability Running Capability
11 Cylinder identification sensor No normal signals are received from the cylinder identification sensor Continues to operate the engine based on the results of the cylinder identification that existed up to that point Unable Able
12 Crankshaft position sensor No normal signals are received from the crankshaft position sensor Stops the engine (by stopping the injection and ignition) Unable Unable
13
14 Intake air pressure sensor (open or short circuit) (pipe system) Intake air pressure sensor-open or short circuit detected.
Faulty intake air pressure sensor system Fixes the intake air pressure to 85.0 kPa. Able Able
15
16 Throttle position sensor (open or short circuit) (stuck) Throttle position sensor-open or short circuit detected Fixes the throttle position sensor to fully open Able Able
20 Intake air pressure
Atmospheric pressure Defective values are detected due to the internal malfunction Fixes the intake air pressure and atmospheric pressure to 85.0 kPa. Able Able
21 Coolant temperature sensor Coolant temperature sensor-open or short circuit detected Fixes the coolant temperature to 600 C. After the engine starts, the radiator fan relay will be turned on. Able Able
22 Intake temperature sensor Intake temperature sensor-open or short circuit detected Fixes the intake temperature to 00 C. Able Able
23 Atmospheric pressure sensor (open or short circuit) Atmospheric pressure sensor-open or short circuit detected Fixes the atmospheric pressure to 85.0 kPa. Able Able
30 Oil pressure dropped Engine stops when the oil pressure drop is detected Fuel pump and fuel injection are stopped (main relay is off) Unable Unable
33
34
35
36 Faulty ignition Open circuit detected in the primary lead of the ignition coil Cut the injection of cylinder in the same group with the cylinder that the error is detected. Example, when the #1 cylinder is defective, cut the injection of #1 and #4 cylinders. Turn on the power to the air induction solenoid to always cut-off the aire Able (depending on the number of faulty cylinders) Able (depending on the number of faulty cylinders)
42 Speed sensor No normal signals are received from the speed sensor Assumes highest ratio Able Able
43 Fuel system voltage (monitor voltage) The ECU is unable to monitor the battery voltage (an open circuit in the line to the ECU) Fixes the battery voltage to 12 V Able Able
44 Error in writing the amount of CO adjustment on the EEPROM An error is detected while reading or writing on the EEPROM (CO adjustment value) n/a Able Able
46 Vehicle system power supply (monitor voltage) Power supply to the FI system is not normal Grip warmer output is off Able Able
50 ECU internal malfunction (memory check error) Faulty ECU memory. When this malfunction is detected, the code number might not appear on the meter n/a Unable Unable
80 Grip warmer switch Grip warmer switch-short circuit detected n/a Able Able
81 Grip warmer Grip warmer-open or short circuit detected n/a Able Able
82 Thumb warmer switch Thumb warmer switch-short circuit detected n/a Able Able
83 Thumb warmer Thumb warmer-short circuit detected n/a Able Able
84 T.O.R.S. Detecting conditions for T.O.R.S. are satisfied n/a Able Unable
85 Oil pressure switch Oil pressure switch-open circuit detected n/a Able Able
- Start unable warning Relay is not turned ON even if the crank signal is input while the start switch is turned ON. When the start switch is turned ON while an error is detected with the fault code of number 11, 12, 30, or 50. Engine trouble warning light flashes when the start switch is turned on Unable Unable

 

[shiznitt100]

trying to post a service manual for 2006-2009 apex the file is 16mb and having a hard time posting it, i will try to split it up to 2 downloads. has all codes, all mechanical, ect. it is a complete yamaha not the crap haynes

 

[Rob1334]

Look how helpful this banned man is!!!!

 

[shiznitt100]

i guess i have been away too long i missed the banning lol sorry to hear jbb thanks for the codes

 

[RWoods]

This may be a silly question but do these codes apply to the Venture sleds as well. Father in laws sled is coming up with a 00021 Oil flashing in the display.

Any help would be great.

 

[shiznitt100]

does the oil light go out or does it stay on?, if you roll a yamaha the light will stay on for a few mins then should go out. check your oil level and sender. make sure it has good contact, also check connector at comp at front of sled, make sure there is no water in the connector

 

[crosroads]

Thanks for the info, should come in handy someday.... wonderin if they apply to the phazer too?

 

[RWoods]

Oil light does not come on at all. Oil 00021 just flashes on the display screen. Have checked all levels and all connections but still no changes. Has been in the garage so water wont be an issue. Got any ideas??

 

[shiznitt100]

give trent a call at walt healy. he runs the service department. he is a good guy and very fair if he has to charge something. he has helped me out alot in the past

 

[cjfexist]

can you help me out with trouble shooting code 81. Im aware that it has to do with my hand warmers, just lookin for hints to make them work!

 

[goodngrubby]

can you help me out with trouble shooting code 81. Im aware that it has to do with my hand warmers, just lookin for hints to make them work!

Chances are that one is burnt out. I had the 81 code blinking on a Phazer, all the wiring and such was good. It turned out to be a dead warmer.

 

[tjbutina1]

Oil light does not come on at all. Oil 00021 just flashes on the display screen. Have checked all levels and all connections but still no changes. Has been in the garage so water wont be an issue. Got any ideas??

That means you have gone 21 miles past your scheduled oil change, as you ride the 00021 will increase.

 

[jhowson]

Hey my 09 mtx is popping code 84 aft i gave it a bath and installed a cable off the battery for a heated visor, any thoughts?

 

[suzuki_ryder]

Hey my 09 mtx is popping code 84 aft i gave it a bath and installed a cable off the battery for a heated visor, any thoughts?

The beginning of the thread has a legend of all the codes. 84 is the throttle override system.


Sent from my iPhone using Tapatalk

 

[jhowson]

Thank you, I was looking for a possable cause and maybe a solution, as it just started after i washed it, and installed that cable.

 

[suzuki_ryder]

You said you had a code 84 after giving it a wash and were looking for thoughts

Your throttle override switch is frozen in so it thinks your throttle is stuck. Put it in a heated garage for a few hours.


Sent from my iPhone using Tapatalk

 

[suzuki_ryder]

Delete

 

[overkill131313]

I have a code 20 and it is blowing a fuse by the starter solenoid......any one help me? I have to figure out what this fuse is for but when it blows the fuel pump stops! I can cycle the fuel pump for 5 mins buy turning the key on and off for 5 mins.....fuse stays good.....if I start sled it will run for 20 seconds then blow the fuse. WTF!

code 20 is: 20 Intake air pressure
Atmospheric pressure Defective values are detected due to the internal malfunction Fixes the intake air pressure and atmospheric pressure to 85.0 kPa. Able Able

every sevice manual that I have found is different than what I need....I need to find out what the two fuses on the solenoid are for.....the manual shows one main (30 amp) and that is it.....I have that one plus 2 10 amp fuses on each side......one of these is the one that keeps blowing!