What Did You Do In Ur Garage?

[overkill19]

Bought a Di-Acro brake today. Cleaning off the surface rust. Been hunting for a 24” for a long time!!!

 

[DaveB]

I did the CAI and Burnbox on the Challenger a while back. Pulled 'er out of the corner today and put 'er up. Solid lug nuts, Powerstop brake pads, Performance Development DIRS diff brace, and Demon driveshaft going on next. (in preparation for wider rep wheels and drag radials....next...assuming I can afford)

 

[4extreme]

I`m currently building some RV trailer stabilizers. I seen them at an rv show and checked into the price...yikes!. ~$350 US. So I decided to build a set. going to cost me around $125(ca). They may not be powder coated or as pretty as the $350US set but they will work just as good

 

[doorfx]

I`m currently building some RV trailer stabilizers. I seen them at an rv show and checked into the price...yikes!. ~$350 US. So I decided to build a set. going to cost me around $125(ca). They may not be powder coated or as pretty as the $350US set but they will work just as good

Can you post a link ?

 

[doorfx]

I did the CAI and Burnbox on the Challenger a while back. Pulled 'er out of the corner today and put 'er up. Solid lug nuts, Powerstop brake pads, Performance Development DIRS diff brace, and Demon driveshaft going on next. (in preparation for wider rep wheels and drag radials....next...assuming I can afford)
//uploads.tapatalk-cdn.com/20200409/93ef8de4e98c2e1cdbefbfe4e67b90da.jpg

You need a lift !!

 

[DaveB]

You need a lift !!

I do....but I only have 12' ceiling. This is the first time I jacked up the Challenger....it is STIFF! My intent was to do a jack on each side, do a bit at a time, front first, then the rear. Well hell...I started popping up one front side, go to the other and the lift point is lifted above the jack......pump that side up, go to the other side and the lift point is over.... LOL. The rear was the same. It wouldn't droop a 1/4" from side to side. Holy hell....my oll Dart if I jacked one corner, the other 3 wheels stayed on the ground until I got it 7-8" in the air!

 

[doorfx]

Lol that was funny

 

[Pistonbroke]

I do....but I only have 12' ceiling. This is the first time I jacked up the Challenger....it is STIFF! My intent was to do a jack on each side, do a bit at a time, front first, then the rear. Well hell...I started popping up one front side, go to the other and the lift point is lifted above the jack......pump that side up, go to the other side and the lift point is over.... LOL. The rear was the same. It wouldn't droop a 1/4" from side to side. Holy hell....my oll Dart if I jacked one corner, the other 3 wheels stayed on the ground until I got it 7-8" in the air!

Do it - I’ve got 12’ ceilings with an 11,000 lb Snap-on (Wheeltronic) lift in mine. Best thing ever...

 

[arff]

I have one small section of garage to finish painting and cleaning. Have a L shaped garage so just the last of the long end.

14 days of isolation in March I had time to do a lot of painting and cleaning.

 

[catalac]

I did the CAI and Burnbox on the Challenger a while back. Pulled 'er out of the corner today and put 'er up. Solid lug nuts, Powerstop brake pads, Performance Development DIRS diff brace, and Demon driveshaft going on next. (in preparation for wider rep wheels and drag radials....next...assuming I can afford)
//uploads.tapatalk-cdn.com/20200409/93ef8de4e98c2e1cdbefbfe4e67b90da.jpg

This late spring must suck when you have those wheels wanting to go for drive.

 

[kingcat162]

Sled fixing

 

[doorfx]

Finally got my parts in. Finished off the front u-joint. Man I need a lift!!lol

 

[doorfx]

Now to fill up the fuel and get the camping stuff ready.

 

[DaveB]

Brake pads swapped.

 

[Couch]

Picked up a tractor last month and now stripping it down to clean and paint cab .. .previous owner used for snoclearing only but obviously didn't pressure wash and clean before summer storage. Getting cab blasted, primed plus epoxy top coat. Will brush on bedliner on fenders and cab floor ....
That will keep me busy for a couple more days of lockdown ...will tackle blower next ....

 

[sirkdev]

funny I was thinking of doing the same thing..

 

[Go-Vertical]

 

[Go-Vertical]

Little fixer upper for my son.

 

[4extreme]

Can you post a link ?

are you looking for a link to the ones made in the USA or the ones I`m making? the one set I seen from the US https://store.lci1.com/jts-strong-arm-jack-stabilizer-kit-various-sizes-jt-strng-arm.html I will take some pics of mine when I`m done.

 

[doorfx]

Yes the ones you are making , thanks.
Are you planning on making some to sell?