Rebuilding the quad, progress pics.

[leonard]

Lets go hit the Buck Creek rally next summer....I'll tow 'er out on it's side again....HAHAHAHA.

maybe this time you will use ropes around the tires or something as to not scratch off the chrome.

 

[Captjacksparrow]

where did you get the powder coat done

Metal Strip & Coatings in Red Deer. Very good job. I've been using Gary for years and never had a bad job. I've had tunnels done and they looked awesome after years of use.

 

[Captjacksparrow]

Couple of more pics. I finally got the gauges done, and did a small race cut on the front fenders. Got my billit oil catch can, and wheelie bar assembled. Waitin on motor stuff now.

 

[SledMamma]

That machine looks crazy-azz fun!! Too bad it's gonna be too puurrrty to ride anywhere but your garage pad

I'm looking at all these pics and thinking I should put you to work on my quad this spring...

 

[Hitchguy]

looks good but agree with SledMamma, it's not going into any mud or water :d:d

 

[STYKO]

Nice pics !!!!!!!!!!!

 

[off road rider]

where did the CF parts come from??

 

[quadboy55]

where did the CF parts come from??

If I had to take a guess, I'd say the plastics came from Maier. If they are, then they are just a CF print.

 

[leonard]

looks good but agree with SledMamma, it's not going into any mud or water :d:d

or anything.. trails .. dirt roads .. service roads.

and i cant think of any Drag strips that race ATVs around here..

lol you should'a thrown Dune tires on it and hit some of the local dunes and pwned everyone.

 

[leonard]

btw it looks amazing man.

but most important thing is you get out and use it.

 

[rzrgade]

I hear it get`s to Brule once in a while...lol

 

[DaveB]

I hear it get`s to Brule once in a while...lol

...and Rexburg...

Boost guage eh Cap'n Jack? Hmmmmmm...

 

[mustange70]

Soooooooooooooooo is there a powerplant going into that thing that will be cause enough for that wheelie bar?

 

[byronkentgraham]

Going to be an incredible machine. I'm waiting for someone to turn the v-force into a 4wd though. It's got the power. Wouldn't way muc more than a renegade.

 

[Captjacksparrow]

Leonard: It's pretty much a dune machine. I will drag race it around here some but we mostly ride St Anthonys in Idaho and other dunes down south. I've been to brule as well.
Mustang70: It's needed the wheelie bar for a while now. Even with a 9" swing arm it would not hold the front down at Brule with out the bar. It's getting a little more power this year as well.
Dave: Boost gauge...........what boost gauge?
Off road rider: The plastics are OEM Kawasaki but they are just plastic with the carbon fiber look. The only thing that's CF on it is the gauge cups.
Here's a pic from last year in St Anns with the dunes tires on it but with a 3" swing arm. It was out of control so I put a 9" swing arm on when I got home. I'm going to try the other set of dune tires this summer to see how they work as well.

 

[GWNBrute]

Looks awsome, good job!

 

[duner]

A 9" swing arm and still walkin out of the hole? WOW! That thing is the nicest quad I've ever seen with the power to match!

 

[DRD]

Jeez Dan, you should run a small paddle on your wheelie bar. You could drive it with a chain off the axle, that way it won't slow you down.

 

[Captjacksparrow]

A 9" swing arm and still walkin out of the hole? WOW! That thing is the nicest quad I've ever seen with the power to match!

I had to come out of the hole at part throttle and slowly get into it and half up the little hill at Brule it would still start to come up again.

Don, that might actually work! :d

 

[davelaw1982]

Soooooooooooooooo is there a powerplant going into that thing that will be cause enough for that wheelie bar?

goin by the little gauge that says boostI'm a thinkin so

Nice one Dan