maxwell
Active VIP Member
Just about fell out of my chair LOL
Gear ratio game changer
- Thread starter maxwell
- Start date
Just about fell out of my chair LOL
Caper11
Active VIP Member
What did he say?
Mountainman52
Active VIP Member
Whats a game changer ?????
snopro
Active VIP Member
Don't leave us in suspense?
ABMax24
Active VIP Member
"ThatSkidooFeeling" hahahahaha lol roflmao. I just fell out of my chair, this is so funny.
Oh wait no it's not, it's just childish
Last edited:
- Thread starter
- #6
maxwell
Active VIP Member
Lol I was just talking about the Polaris title
tmo1620
Active VIP Member
You mean what they been doing aftermarket since 2013, kurts gear down kit and all the others etc.
powpowpowpow
Active VIP Member
He is only doing what he is paid to do. No different than Norona praising every brain fart from doo on clutching updates to keep belt temps below 220f under light load.
Rhodesie
Active VIP Member
don't get too close to him the doo spew will give you the narona virus.
- Thread starter
- #10
maxwell
Active VIP Member
Longhairfreak
Active VIP Member
That's phucking brilliant.
- Moderator
- #12
norona
Active VIP Member
- Joined
- Jan 1, 2009
- Messages
- 2,182
- Reaction score
- 8,044
- Location
- North Vancouver
- Website
- www.noronalife.com
Caper11
Active VIP Member
- Moderator
- #15
norona
Active VIP Member
- Joined
- Jan 1, 2009
- Messages
- 2,182
- Reaction score
- 8,044
- Location
- North Vancouver
- Website
- www.noronalife.com
kimrick
RIP Fellow Sledder
So after looking at the new quick drive 2 videos, it that the brake disc on the top drive?
If you break a belt (quick drive belt) that would mean no braking to the the track?
That would make a steep down hill a possible rodeo ride, no?
Isnt the G4 brake on the lower drive axel so there is still braking capabilities?
I beleive all sleds should have braking abilities on track drive shaft to allow braking under any ciscumstances.
Same goes for a stock tether on all machines.
Could be out to lunch on my observations. Let me know if I am correct or wrong on this.
Cant get an optomitrist appointment (which is much needed for my old eyes) due to them being closed due to virus.
If you break a belt (quick drive belt) that would mean no braking to the the track?
That would make a steep down hill a possible rodeo ride, no?
Isnt the G4 brake on the lower drive axel so there is still braking capabilities?
I beleive all sleds should have braking abilities on track drive shaft to allow braking under any ciscumstances.
Same goes for a stock tether on all machines.
Could be out to lunch on my observations. Let me know if I am correct or wrong on this.
Cant get an optomitrist appointment (which is much needed for my old eyes) due to them being closed due to virus.
SnowJunkie82
Active VIP Member
You are correct. Polaris has for years run the brake on the end of the jack shaft. Both on the belt and chain drive systems. Have yet to hear of an incident where a belt or chain failure and subsequent lack of brakes caused further injury or damage. I have only blown one belt and that was on a turbo’d 2013 Pro that I shock loaded jumping a small creek and that was before they had the upgraded belt.
To OP’s original comment. I agree that when you compare a gear ratio change to a production turbo sled you may be left wanting. However, if Maxwell hasn’t he should go for a ride with Mr Adams. Dan is a true Ambassador of the sport who takes great pride in making everyone a better and safer rider. Perhaps Maxwell might have his game changed!
tmo1620
Active VIP Member
Its been like that since 2013 for sure. Two guys i used to ride with rented some 2013 pro rmk back then from blue river and they each blew apart the belts and towing them out of salmon was a chore, there was definite but puckering going on for both those guys
- Thread starter
- #20
maxwell
Active VIP Member
MY 2000 zx had a brake rotor on the jackshaft. Just sayin
Similar threads
