Cold air intake kit problem

kwseba1

Active member
Joined
May 22, 2012
Messages
26
Reaction score
11
Location
grande prairie
I have had issues with my cold air intake kit. Its great most of the time, however, when the snow conditions are just right (with a couple of feet of new fresh powder and cold weather) I find that I end up with snow covering the cold air intake. I contribute a bog and lousy throttle response to this. I have taken the shroud out so that it takes in warm air from the engine, hoping that it would fix it. I would give up cold dense air to at least have better throttle response. I have frog skins almost everywhere and where I dont I have duct taped. If anyone knows how to fix this problem it would be greatly appreciated. I know its alot to ask but could I get serious feedback. lol. Im talking about you doo guys. I know what your going to recommend... a xm. Id like to see if I cant fix it first. thanks anyway!
 

Slamnek

Active VIP Member
Joined
Nov 14, 2006
Messages
2,826
Reaction score
1,570
Location
Kitscoty
I had the D&D fire breather intake on an 09 M8 and i rode the deepest powder of my life last year and only had one stuck due to bogging out with a pile of snow on the hood. I never once had snow under the hood piling up around the filter.
 

0neoldfart

Active VIP Member
Joined
Nov 22, 2008
Messages
1,385
Reaction score
2,632
Location
Thorsby
My solution was putting a skinz airframe hood on my M1000, and modifying the stock airbox. I have tried the BDX cold air intake, but wasn't very impressed with it especially in fine powder snow. The M1K needs to breathe, the stock box with minor mods seems to work the best, and certainly more consistant...but a mesh hood is the way to go in terms of performance
 

joekikass

Active VIP Member
Joined
Nov 1, 2010
Messages
178
Reaction score
171
Location
devon
Stock air box with some flow rites and skins work best for cats, you get fresh air rather than hot engine air, moisture and an iced up intake
 

Catberg

Active member
Joined
Oct 23, 2008
Messages
67
Reaction score
82
Location
Fort McMurray/ Campbell River
I went with the timbersled intake on my 2010 M1000 with slp exhaust, boondocker box and Cutler tm weights, bdx secondary with a Cutler torsional update. It gets warm air but never misses a beat now. I just came back from Revy. I didn't see the hood very much the whole time I was there.
 

kwseba1

Active member
Joined
May 22, 2012
Messages
26
Reaction score
11
Location
grande prairie
so... Im just wondering, did you have the bdx cold air kit and take it off, or did you always have the timberled one on? How is the timbersled one different, Im not familiar with it.
 

Mr Doo

Member
Joined
Jan 19, 2009
Messages
6
Reaction score
2
Location
Fort st John BC
Hey there Joekikass, where did you cut in for your flo rites ? I have the same issue of icing up and from all of the suggestions here I like yours the best, can you upload any pictures ? Thanks.
 

cat925

Active member
Joined
Feb 16, 2010
Messages
68
Reaction score
101
Location
edmonton
Hey there Joekikass, where did you cut in for your flo rites ? I have the same issue of icing up and from all of the suggestions here I like yours the best, can you upload any pictures ? Thanks.
Stock air box is best with the proper mods joekikass did it right post some pics joe help us out
 

summitbound

Active VIP Member
Joined
Nov 20, 2006
Messages
216
Reaction score
58
Location
Benalto,AB
Arctic-Cat-Air-Box-Vent.jpg www.moflowvents.com
 

joekikass

Active VIP Member
Joined
Nov 1, 2010
Messages
178
Reaction score
171
Location
devon
image.jpg

Just hole saw two holes, clean out and giver! You can also replace your air horn for better flow
 

Team Pigeon

Active VIP Member
Joined
Oct 31, 2007
Messages
265
Reaction score
362
Location
Pass Creek.
What sled are you on? The 1000's are way more susceptible to exhaust bog than the m8's.
If it's a 1000, speedwerx tunnel dumper can.
 
Top Bottom