Anyone try a Jaws pipe on a 18/19 Cat?

[kanedog]

Anybody wanna sell me their pos pipe for a couple hundred? I’ll give this pipe a try. I too like to waste time and money on things things that don’t work. I do it all the time. But I never learn!

 

[E-Zmoke]

Anybody wanna sell me their pos pipe for a couple hundred? I’ll give this pipe a try. I too like to waste time and money on things things that don’t work. I do it all the time. But I never learn!

I’m sure I can round one up for you candycane I might know of a few or half a dozen sitting on shelfs collecting dust, don’t say I didn’t warn you...Mayb the new pipe will be called the bears den instead of the shark? I don’t like shark week

 

[slededjr]

You’ll make it work with some tuning on numbers. Cat had 6 or 7 different flashes on their ECM’s after the Shark was originally designed and dialed in. Ran into similar situation on the ‘12. Simplest thing to do now would be to get the most current flash installed, measure the busing ID on pipe and then message Jaws, Brent or myself and you’ll get numbers that will work.

 

[drew562]

Anyone try the SSI pipe mod?. Reed. Head no tuner needed

 

[CatAttack900]

Is anyone running the powder freaks head this winter on their alpha? Looking of maybe going to pipe and head instead of turbo.

 

[dragonweld28]

I will be testing a SSI 14/1 head and a Jaws pipe and y-pipe this winter.

 

[CatAttack900]

I will be testing a SSI 14/1 head and a Jaws pipe and y-pipe this winter.

So won’t be available till late winter I am assuming?

 

[slededjr]

I will be testing a SSI 14/1 head and a Jaws pipe and y-pipe this winter.

Should work good. Heard some good reviews.

 

[CatAttack900]

Has anyone done anything with Linderman on the new c-tec motor? If so what did you have done and did it perform well!!

Thanks

 

[dragonweld28]

I have some on order. Just havent tested them yet. Should know by January.

 

[Rjjtcross8]

Has anyone done anything with Linderman on the new c-tec motor? If so what did you have done and did it perform well!!

Thanks

Curious on this as well

 

[drew562]

I just had specialty do the SSI head. Pipe. Reeds. Clutching on my alpha. Now I have to wait till NOV to test it. Can’t wait.

 

[Rjjtcross8]

I just had specialty do the SSI head. Pipe. Reeds. Clutching on my alpha. Now I have to wait till NOV to test it. Can’t wait.

Did you go with a jaws pipe or the ssi pipe mod?

 

[niner]

I just had specialty do the SSI head. Pipe. Reeds. Clutching on my alpha. Now I have to wait till NOV to test it. Can’t wait.

Which fuel controller did you go with?

 

[drew562]

Did you go with a jaws pipe or the ssi pipe mod?

The pipe mod. No controller. I could have more power with a jaws and boondocker box. But I wanted to keep it simple. I’m done tinkering on the hills. It should give that little bit extra I’m looking for. The Gearing will be next thing I play with. .
Oh and It sounds real good in the garage. Lol need snow

 

[zbmmike]

Does anyone have any updates yet ? SSI kit? New jaws pipe?

Thanks

 

[Kibbels]

The pipe mod. No controller. I could have more power with a jaws and boondocker box. But I wanted to keep it simple. I’m done tinkering on the hills. It should give that little bit extra I’m looking for. The Gearing will be next thing I play with. .
Oh and It sounds real good in the garage. Lol need snow

Ummm how are you planning with no controller?

 

[Slamnek]

I emailed BD Extreme and Erich Long assured me that you do not need a fuel controller when running the pipe mod and even with the Y pipe too. I specifically asked if I needed a controller if I I rode below 2000 feet and he said no.