What did you do to your UTV today?

[bigdawg]

Or could be the lift, arched arms and 32" rubber...

Nice ride Dawg. Got the tow-truck setup for pulling the SxS's with stock (broken) axles I see. Haha

10-4 that 1 Dave, lots of broken axles last yr as well as I'm to old and fat for the kids dirt bikes, now through them up on the deck or hoist them across the muskeg holes .

 

[teeroy]

ya buddy I love it, I told Nette we should try and do the grande cache bash this yr

dude, you totally should, would be awesome to camp out and ride with you guys again....i think we have the tabsters considering attendance this year as well, would be an awesome time even just to hang out again

 

[psullivan]

finished building and installing a clutch cover for my apex rzr


Sent from my iPhone using Tapatalk

 

[neilsleder]

Got done build my snorkels! Took way longer then I thought it would


Sent from my iPhone using Tapatalk

 

[camoJoe]

Got done build my snorkels! Took way longer then I thought it would


Sent from my iPhone using Tapatalk

Looking pretty good neil, !!!

 

[camoJoe]

washed our toys for a few hours , lots of mud, lots of winching had a great ride !!!

 

[rzrgade]

Got done build my snorkels! Took way longer then I thought it would


Sent from my iPhone using Tapatalk

You must be tall..........

 

[neilsleder]

You must be tall..........

lol no just wanted them up out of the way past my head so they make as much noise

 

[rzrgade]

Well made a long list of "additions" for the wildcat.....
Fenders, then more fenders.........!!
Drill holes & more holes.....Drainage
A arm guards
Install that pesky runva winch
Design some hub caps that stay on the wheel for more than an hour
A rear view mirror ......(canam) mirror for short
Better storage box
Arched rear lower radius rods

Not bad for a stock machine....lol
Did get the the preload & dampening tuned up a bit today......Set it at about 18/19 inchs GC, up about 4 inchs from stock ride height. Axle angles are very nice at a conservative 20 ish degrees...

Along with 6 clicks up on the podiums and it rode great !!

Just need the time to build some of this chit........lol

 

[High Velocity]

Well made a long list of "additions" for the wildcat.....
Fenders, then more fenders.........!!

LOL !! That's the only thing I'm battling with on my RZR 1000. Holy crap, do you get dirty in this thing, even with full doors !!! I may as well be riding a Renegade !!




Sent from my iPad using Tapatalk HD

 

[imdoo'n]

LOL !! That's the only thing I'm battling with on my RZR 1000. Holy crap, do you get dirty in this thing, even with full doors !!! I may as well be riding a Renegade !!


Sent from my iPad using Tapatalk HD

no don't do that , you'd have a beotch of a time getting that clutch to work. fuel mileage would suck and doo juice likely tastes like american beer. yuck

 

[arff]

Very end of the day. Rim had a rock break it.

Must have jammed by the caliper

 

[imdoo'n]

oh oh, that looks like it won't rub out!!. jb weld to get you out?

 

[arff]

oh oh, that looks like it won't rub out!!. jb weld to get you out?

I have cream

 

[ponyboy]

Snorkles looks good ..... did you have to re-jet /..... if so did you go up or down .... and did you lift or drop the needle

 

[rzrgade]

Thank god for ABS, perfect center wheel caps for a stock wildcat rim !!! Who knew.....

 

[arff]

Spare rim on tire.

Will wash tomorrow.

Will be ready

 

[teeroy]

pulled the rad out of the commander and cleaned it out....bottom 3 inches was pretty caked with mud. built a little shroud to block the mud from coming up under the winch and splashing on the bottom part of the rad. hope it works, relocate is next if it doesn't.

 

[arff]

Looked this morning. Will replace front brake pads before jamboree.

Man am I hard on Brake pads. Must be the 80 km hr driving on power lines and pipelines and slamming on the brakes.

 

[tex78]

Too much wo and not enough go eh

Mabe clutch it so u get some more engine braking