dead bf750

[Joshgrizz660]

hey guys, long time since i have posted on here but saw everyone a couple km from where i was camping on the long weekend, basically i pooched my motor tackeling some nasty stuff soo looking into a full rebuilt with a bbk kit, anyone out ther shed some light as to wich would be best for my machine?, i have an 05 bf750 with some work to her but wanna do a full big bore on it and was looking for pricing aswell as best bbk to go with, any help would be greatly appreciated. thanks alot all, ride hard and safe

 

[jgonie]

i no glen at amr his 800 kit makes big hp or four stroke techs 840 when i had my brute i was looking into the amr 800 kit but sold brute. if you are building it yourself if not try kevin at rapid revolutions

 

[tex78]

my buddy just got his 05 750 brute rebuilt.... went with a fundy 880 kit [ says its the biggest u can with out bigger carbs ect... ] works good has tons of bottom end... and even the jetting is smaller than the stock..... its going to depend on whats total wrong with your [ won't know till ya open her up ] .... his was pretty much all done inside....
think it was close to 4000 all said and done.... also fundy is out of newbrunswick

 

[Joshgrizz660]

thanks alot guys much appreciated, i have been looking into the fundy kits as i have fundy performance in my cams aswell as full exhaust but i could take a small video and fire it up to let you hear what it sounds like, pretty much like a dieing whore in heat haha but 4 g isnt bad from what i have been hearing just i have no one to throw it all togther, money is no object im balls deep in this quad now so may aswell make it the bad boy of the group, amr seems to be a good performance dealer but was thinking going the biggest i can with sumwhat reliability there still, let me know what you have in mind, also if you could point me in the direction of a good mechanic who would like some pocket cash let me know, again thanks alot for the replies!

 

[brutematt750]

fundy is canadian and build good stuff. I think most of it comes down to who puts the motor together.

 

[Joshgrizz660]

this is what i have heard, i may look into going a full fundy bbk aswell as looking at a 3 or 6 inch lift, im in this deep might aswell go HARD. i spend most of my time in the slop and not to much on the trails so may aswell go a big nasty, im looking to do all of this over winter time and be good for next spring, should i go with gorilla axles if i go a big lift? thanks again for the replies, very much appreciated. also if anyone has any phone numbers to these companys that would be great so i can start ordering stuff.

 

[tex78]

this is what i have heard, i may look into going a full fundy bbk aswell as looking at a 3 or 6 inch lift, im in this deep might aswell go HARD. i spend most of my time in the slop and not to much on the trails so may aswell go a big nasty, im looking to do all of this over winter time and be good for next spring, should i go with gorilla axles if i go a big lift? thanks again for the replies, very much appreciated. also if anyone has any phone numbers to these companys that would be great so i can start ordering stuff.

get rino axles from rapid reveloutions in eddy.... 1/2 the price of gorilla and just as good if not better

 

[neilsleder]

I wouldn't go with rhino axles! I got them on my Brute and a have so far wrecked 3 in about 200km. On the splines stripped one the boots were leaking grease and the other snapped off on the outside joint.

 

[Joshgrizz660]

who would you all say would be the best place for me to take my quad for the lift aswell as motor bore? my quad still starts fine but when its running sounds like something has bent and is knocken bad, not 100% sure what i have done yet but i know the motor is not completly toast. will i have to replace my cams aswell? aty first buddys i was with figured it was prolly a bent valve of something due to the sound howling out of it. im looking to get on this withen the next month or so and wanna build her up good. just wanted to know the best of the best. thanks for the replies fellas. much appreciated

 

[tex78]

I wouldn't go with rhino axles! I got them on my Brute and a have so far wrecked 3 in about 200km. On the splines stripped one the boots were leaking grease and the other snapped off on the outside joint.

who would you all say would be the best place for me to take my quad for the lift aswell as motor bore? my quad still starts fine but when its running sounds like something has bent and is knocken bad, not 100% sure what i have done yet but i know the motor is not completly toast. will i have to replace my cams aswell? aty first buddys i was with figured it was prolly a bent valve of something due to the sound howling out of it. im looking to get on this withen the next month or so and wanna build her up good. just wanted to know the best of the best. thanks for the replies fellas. much appreciated

huh i haven't heard of one problem with the rhino's...... my stockers keep busting the shafts right at the inside joint..... so i have one rear rhino in now and so far so good...

talk to captian jack sparrow on here or call him at extreme machines in bentley.... he is the kawi v god.... knows his chit...

 

[tex78]

I wouldn't go with rhino axles! I got them on my Brute and a have so far wrecked 3 in about 200km. On the splines stripped one the boots were leaking grease and the other snapped off on the outside joint.

they have a 1 year warranty so at least ur covered [ i put on 150 hard km a weekend ]

 

[4byrookie]

they have a 1 year warranty so at least ur covered [ i put on 150 hard km a weekend ]

I have had 2 rhino axles for around 5-600km or so and have had no issues at all. I do have a real issue trying to get my thumb off the throttle though(the reason for the axles)

 

[byronkentgraham]

After looking at those rhinos on texs machine I would never get anything but. And have heard some bad things about gorilla axles

 

[tex78]

ya also the gorilla axles have to break in for like 100 km .... they get so hot u can't touch them and the heat pops the boots off.....

rhino 's don't do that.....

 

[Joshgrizz660]

looks like rhinos for me, can you put those axles with like a 3 or 6" lift? also with the rad can you upgrade to a little bigger one if a guy had it? or does it have to be made for the bf750? and as for the best most reasonably priced bbk's who does the best work for reliablity? looking to get on this fairly soon so by next season she is good to go, all your guys help has been very much appreciated,

 

[Joshgrizz660]

any of you all ever heard of turner cycle out of texas? was just on there site and was reffered by my mechanic but they have some serious lifts with custom cv's, was just wondering if anyone had tried these,

 

[tex78]

looks like rhinos for me, can you put those axles with like a 3 or 6" lift? also with the rad can you upgrade to a little bigger one if a guy had it? or does it have to be made for the bf750? and as for the best most reasonably priced bbk's who does the best work for reliablity? looking to get on this fairly soon so by next season she is good to go, all your guys help has been very much appreciated,

well me and a buddy have 2 rads.... bottom one can plug up all it wants... never over heat.... winch works better cause the fans not allways runnig and quad has more power cause its cooler.... hooked the hoses in series and it works awsome

 

[rzrgade]

any of you all ever heard of turner cycle out of texas? was just on there site and was reffered by my mechanic but they have some serious lifts with custom cv's, was just wondering if anyone had tried these,

Turners will run you 800$ an axle or 3000 $ + Rhinos under 300$ an axle....................

 

[Joshgrizz660]

well rhinos it is, i have decided instead of doing a bbk just get her fully rebuilt cuz i had more then enough power before and just go with the axels with a 6" catvos lift, nothing but mud for me! ive been looking for pricing on the 6" lifts in canada and they look to be abit steep but you pay for quality, whats the best 6" lift you guys would recomend?

 

[brutematt750]

have you thought about doing a std bore high compression kit? fundy makes one that is suppose to be awesome....just a thought , thats what i think i'm gonna do if and when mine craters. As for the lift I have no idea, catvos makes good lift from what i've read but there pricey. Catvos makes a 4" thats suppose to be a lot easiers on cv's.