Rhino 700 Radiator Relocate

Puffer99

Active member
Joined
Mar 8, 2009
Messages
58
Reaction score
16
Location
Blackfalds, AB
I am just finishing up my rad relocate on my rhino and thought I would post some pics. I used 3/4 heater hose for the rad and 3/8 oil line for the oil cooler. I flared the ends of the oil lines where I cut them so they won't slip off under pressure and I made the brackets out of 3/4 x 1/8 flatbar. In total this only cost around $30 and an afternoon. I am still going to paint it and make a gaurd for the front to protect me from bumping it and the rads from rocks while hauling it on my trailer.
 

Attachments

  • IMG_1881.jpg
    IMG_1881.jpg
    70.3 KB · Views: 328
  • IMG_1883.jpg
    IMG_1883.jpg
    74.1 KB · Views: 287
  • IMG_1884.jpg
    IMG_1884.jpg
    72.3 KB · Views: 317
  • IMG_1887.jpg
    IMG_1887.jpg
    113.5 KB · Views: 298
  • IMG_1890.jpg
    IMG_1890.jpg
    77.3 KB · Views: 276
  • IMG_1888.jpg
    IMG_1888.jpg
    84.8 KB · Views: 270
  • IMG_1886.jpg
    IMG_1886.jpg
    78.9 KB · Views: 267

T-GUY1978

Active VIP Member
Joined
Jul 27, 2008
Messages
344
Reaction score
6
Location
Edmonton,AB
That looks good gunna have to show my buddy the pics he was thinking of doing the same thing.
 

burnt toast

Active VIP Member
Joined
May 6, 2009
Messages
353
Reaction score
243
Location
Calgary / Crowsnest
Hey puffer just wondering how this set up has been working for? Thinking of doing the same thing on mine. Noise? Do's and dont's?
 

Puffer99

Active member
Joined
Mar 8, 2009
Messages
58
Reaction score
16
Location
Blackfalds, AB
It has been working perfectly for a year now! No more problems at all! The only downfall to it is it does restrict your vision a bit when backing up, but I look out the door instead. I would recomend moving the rad on any rhino that plays in the mud much! As far as do's and don'ts go, I really don't have many. Just tie your hoses up good and make sure there aren't any kinks and are not rubbing anywhere and go ride! You will never have to worry about a plugged rad again!
 

Snowdin

Active VIP Member
Joined
Nov 28, 2007
Messages
946
Reaction score
751
Location
Whitecourt
No wonder it was over heating. I may have to re-locate mine too.
 

Attachments

  • Back Rhino Rad [640x480].jpg
    Back Rhino Rad [640x480].jpg
    118.9 KB · Views: 237
  • Front Rhino Rad [640x480].jpg
    Front Rhino Rad [640x480].jpg
    112.1 KB · Views: 229

Puffer99

Active member
Joined
Mar 8, 2009
Messages
58
Reaction score
16
Location
Blackfalds, AB
Yeah, they are next to impossible to get clean without pulling the rad after every ride. Moving it was way easier! LOL
 

burnt toast

Active VIP Member
Joined
May 6, 2009
Messages
353
Reaction score
243
Location
Calgary / Crowsnest
Snowdin that is exacty why i'm moving mine.. Funny, nothing like stopping every .5 mile to let your ride cool down..
 

Snowdin

Active VIP Member
Joined
Nov 28, 2007
Messages
946
Reaction score
751
Location
Whitecourt
Snowdin that is exacty why i'm moving mine.. Funny, nothing like stopping every .5 mile to let your ride cool down..

I know. My last ride was the Edson rally and had to stop every .5 or so. Was very frustrating. I had a bit of a time getting the rad out but now that I know how to do it, it shouldn't be to bad for the next time.

I just can't figure out why the manufactures wouldn't put the rads as high as possible. Yamaha could have located the air box somewhere else and put the rad way up top.
 

burnt toast

Active VIP Member
Joined
May 6, 2009
Messages
353
Reaction score
243
Location
Calgary / Crowsnest
Just an update > I mounted my rad pretty much just like puffer99's. I found that i had to order 7/8" heater hose 3/4 was to small and 3/8 as well for oil lines. Ran it up to temp and kicks in at 180 and within 20 sec. it quits and drops 20deg. Semms to be working awsome. Leaving for Kelowna i will post some pictures when i get back. Later
 
Last edited:

tomanytoysnotnuftime

Active VIP Member
Joined
Feb 21, 2010
Messages
237
Reaction score
97
Location
fort saskatchewan
Moving the rads is a super idea and works very good but it sure is a pain in the ass routing heater hose's where they were not meant to go. At least on a Teryx, not sure how bad it is on other brands. The pics look good, pretty decent looking install.
 

dwolfey

New member
Joined
Aug 8, 2010
Messages
2
Reaction score
0
Location
Alberta, Canada
Hey everyone!

'06 660 here and I love the set up Puffer99! Those rads are pretty tuff to keep clean of mud. I plan on relocating my rad too with a few ideas of my own. I will post those pictures when I am done. On another note, I built a quick little rad washer for less than a hundred bucks, 12v, pressurized and it all stores in a rubber maid container that fits under your drivers seat. Instead of stopping all the time I have found that if you strategically time when you rinse your rad (lunch break, beer break, close to water source, etc.), you can run all day with no problems. I will post more about that in another topic. Thanks for the great ideas !!! :beer:
 

burnt toast

Active VIP Member
Joined
May 6, 2009
Messages
353
Reaction score
243
Location
Calgary / Crowsnest
Here are a few pictures of it roughed in just like Puffer99. Got about 15hrs on it since doing this and it works awsome hasn't over heated once.
 

Attachments

  • Rad Relocate3.jpg
    Rad Relocate3.jpg
    62.8 KB · Views: 208
  • Rad Relocate4.jpg
    Rad Relocate4.jpg
    70.9 KB · Views: 194
  • Rad Relocate5.jpg
    Rad Relocate5.jpg
    77.9 KB · Views: 191
  • Rad Relocate6.jpg
    Rad Relocate6.jpg
    72.4 KB · Views: 189
Top Bottom