13' Mini Boat Build

ABMax24 · Jul 3, 2015

So here is my build thread for my 13' BrattJet MiniBoat. I had both the hull and intake housing built by BrattJet, and I am using a complete 2007 Seadoo RXP 215 for a donor motor. I picked up my hull on the 24th and have slowly been progressing since, trying to work on it when I can after work and on weekends. I also built my own trailer for it, and have since got a VIN assigned to it.
Here's a start of the trailer:

Picking up the boat from BrattJet:

Start of a fuel tank:

Intake housing in:

neilsleder · Jul 3, 2015

That's cool!

Sent from my iPhone using Tapatalk

Toyboy · Jul 3, 2015

Very cool!! I have a buddy building one too. If you don't mind me asking what did the hull and intake cost from brattjet?

ABMax24 · Jul 4, 2015

Toyboy said:
Very cool!! I have a buddy building one too. If you don't mind me asking what did the hull and intake cost from brattjet?

Thanks, is he building a BrattJet, Eagle, or building the hull himself? I was just over $10k with this one by time i walked out the door, but i got it stretched 6" from 12' 6" to 13', and got a 3/8" keel welded in, plus a couple steering parts. I think their goal with these is to have guys running on the water in the $20k-$25k range depending on what you pay for the donor motor, and other options obviously.

Toyboy · Jul 4, 2015

Building himself. The first one was a 10 ft with a 580 seadoo engine and the next one he has an 800 to put in it. He bought plans for the hull and bought enough material for three hulls. What was your reason for stretching it 6"?? I would be happy with 12'6" as 10ft is too tight.

ABMax24 · Jul 4, 2015

Toyboy said:
Building himself. The first one was a 10 ft with a 580 seadoo engine and the next one he has an 800 to put in it. He bought plans for the hull and bought enough material for three hulls. What was your reason for stretching it 6"?? I would be happy with 12'6" as 10ft is too tight.

I went a 6" longer just for a touch more leg room and room in the boat, that and 13' would seem to put the superstitious people off a little. That and I figure it might make it a little more stable especially with 215hp pushing it lol

ABMax24 · Jul 5, 2015

So I managed to get the motor situated and bolted in yesterday, probably pulled it in and out about 4 times to finally get it though. Apparently there are very few places on these motors that are square or level to the crank to get everything lined up, but I did manage to find some.

That motor actually looks a little small in the hull, but should leave lots of room for everything else that still has to go in.

Absledder · Jul 5, 2015

Well it's normally made for someone to sit overtop it and straddle it so it has to be small but I think with 200+ horses that'll be a sweet little boat when your done!

neilsleder · Jul 5, 2015

I am so jealous right now. I would love to be building my own. One day.

Sent from my iPhone using Tapatalk

neilsleder · Jul 5, 2015

You doing all your own welding?

Sent from my iPhone using Tapatalk

ABMax24 · Jul 5, 2015

neilsleder said:
You doing all your own welding?

Sent from my iPhone using Tapatalk

Yeah I am, just got a little Miller 211 with a spoolmate 100, it would be a little small to build a complete hull, but seems to work alright for the welding i have to do on it.

neilsleder · Jul 5, 2015

I got pretty much the same set up. They actually weld really well.
I like this thread and will be following it closely

Sent from my iPhone using Tapatalk

ABMax24 · Jul 5, 2015

So here's what little i got done today, I took the stock muffler and modified the inlet nozzle so i could position better it within the hull.
Before

After with the nozzle moved and muffler bolted in. Also shown is the mounts for the fuel tank i also built, but not yet welded in.

J-Roc · Jul 6, 2015

Subscribed!

I'm thinking about a Yamaha 1200 in an Eagle hull. The sea doo would make the most sense, but would put the project over budget I think.

Awesome! Keep posting build shots! This is great!

ABMax24 · Jul 6, 2015

J-Roc said:
Subscribed!

I'm thinking about a Yamaha 1200 in an Eagle hull. The sea doo would make the most sense, but would put the project over budget I think.

Awesome! Keep posting build shots! This is great!

That's kinda what I started out thinking too, I was going to build a boat around an 800cc seadoo but then started to believe that it would lack a little on power and if I was going to be spending all the money on a hull and everything else I might as well put the engine I wanted in it. That and these motors are fairly common so parts are relatively easy to come by. These motors are also fairly compact as well, so almost exactly half of the interior room will be left for the occupants and a little bit of storage.

RhinoWhino · Jul 8, 2015

That would be way funner than washen mud off of a sxs all the time !!!!

ABMax24 · Oct 10, 2015

Sorry guys, been busy the past few months, between holidays, work and school the boat has taken a back seat. But here it is, finally got it on the water last week. Had a few setbacks, had to change the headgasket on the motor as it was pushing oil out from the high pressure supply to the head. I still need to build the motor cover, roll cage, reverse lever, and add all the switches to the dash. But it does 97km/hr gps with 2 180 lb guys and half a tank of fuel.

ABMax24 · Oct 10, 2015

Clode · Oct 10, 2015

that is pretty sweet, thanks for the update :d

ABMax24 · Oct 10, 2015

Clode said:
that is pretty sweet, thanks for the update :d

Thanks, I'm really impressed with how it performs, the hull is incredibly predictable and agile, not to mention its pretty easy on fuel too. I'll try to get more pictures up shortly.

13' Mini Boat Build

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Active VIP Member

Similar threads